Automotive
Molded gaskets, o-rings and radial shaft seals
Advantages
- very low sieve residue
- good mixing and dispersion properties
- long flow time with short vulcanization time
- easy deflashing
- low compression set
- good resistance against fuel, oil, water, acid
- avoidance of mold fouling caused by filler
Recommended Products
Guide Formulations
| Quarter light gasket, nitrosamine reducing; 65 Shore A; EPDM; sulfur cure, injection molding (K 91-59) | |
| Quarter light gasket, Renault 2 6 07 B1; 60 Shore A; EPDM; sulfur cure, injection / transfer molding (911 C 152) | |
| Corner molding for sponge seals; 30 Shore A; EPDM; sulfur cure (A.1.4.002) | |
| Quarter light gasket; 50 Shore A; EPDM; sulfur cure (A.4.0.003) | |
| Parts with moderate resistance to lubricants and fuel, thermally stressable 100-130°C; 70 Shore A; CR; injection / transfer molding (T.I.B. 4.1.2) | |
| Rear light gasket, Bosch VS 15441; 25 Shore A; PNR; sulfur cure, injection molding (RRS 12) | |
| Silencer mounting; 55 Shore A; NR; sulfur cure (RRS 15) | |
| Resistant to Diesel and rape-oil methyl ester (RME); 65 Shore A; HNBR; peroxide cure (RRS 36) | |
| Gasket and O-Ring, Aktisil Q versus carbon black N-550, according to PSA S22 5106; 60 Shore A; AEM; diamine cure (M 621.7/1) | |
| Gasket and O-Ring, Aktisil Q versus carbon black N-550, according to PSA S22 5106; 60 Shore A; AEM; diamine cure (M 621.8/8) | |
| Gasket and O-Ring, Aktisil Q versus carbon black N-550, according to PSA S22 5106; 60 Shore A; AEM; diamine cure (M 621.8/9) | |
| Gasket and O-Ring, Aktifit AM in combination with silica in AEM; 70/80 Shore A; AEM, diamine cure (AEM 9913) | |
| Gasket and O-Ring, Aktifit AM in combination with silica in AEM; 70/80 Shore A; AEM, diamine cure (AEM 9914) | |
| Gasket and O-Ring, Aktifit AM in combination with silica in AEM; 70/80 Shore A; AEM, diamine cure (AEM 9919) | |
| Molded parts for automotive seals, ASTM D2000, replacement of carbon black N-990; 70 Shore A; NBR; sulfur cure (M 630.0/1) | |
| Molded parts for automotive seals, ASTM D2000, replacement of carbon black N-990; 70 Shore A; NBR; sulfur cure (M 630.0/7) | |
| Molded parts for automotive seals, ASTM D2000, replacement of carbon black N-990; 70 Shore A; NBR; sulfur cure (M 630.0/3) | |
| Molded parts for automotive seals, ASTM D2000, replacement of carbon black N-990; 70 Shore A; NBR; sulfur cure (M 630.0/2) | |
| Molded parts for automotive seals, ASTM D2000, replacement of carbon black N-990; 70 Shore A; NBR; sulfur cure (M 630.0/5) | |
| Molded parts for automotive seals, ASTM D2000, replacement of carbon black N-990; 70 Shore A; NBR; sulfur cure (M 630.0/6) | |